Otto Bock Kenevo 3C60 Page 82 Introduction Manual Download

Page: 82 / 241

| © Ottobock

Kenevo Protective Cover

•

The 4X840 Kenevo Protective Cover, including
the 4P8 Distal Cap, is only compatible with
3C60* Kenevo

•

Protects the 3C60* Kenevo including AXON
Tube Adapter against environmental
influences and wear and tear

•

The Protective Cover is individually length
adjusted by the technician

•

Main Protector Unit can be donned and doffed
by the amputee

•

Charging the knee joint is possible with
mounted Protective Cover (also through
clothing)

Component selection

Component selection | Kenevo 3C60 | Prosthetic | Global Academy | 22.11.2020

see

manual

Summary of Contents for Kenevo 3C60


















































































































































































































































Search results

Summary of Contents for Kenevo 3C60

Reviews:

Related manuals for Kenevo 3C60

Brands by name

Popular brands

Otto Bock Kenevo 3C60, Introduction Manual

Search results

Summary of Contents for Kenevo 3C60

Reviews:

Related manuals for Kenevo 3C60

Brands by name

Popular brands