Otto Bock Kenevo 3C60 Page 135 Introduction Manual Download

Page: 135 / 241

| © Ottobock

BionicLink PC

Using

BionicLink PC for bilateral fitting

•

Open the DataStation twice and
select K-Soft in each window)

•

Connect to the first component
with the first instance of the
adjustment software

•

Connect to the second component
with the second instance of the
adjustment software

TWO

BionicLink PC dongles are available and two Kenevo have to be

adjusted, it is possible to work parallel with

TWO

instances of the adjustment

software (e.g. bilateral fitting):

1. Left

2. Right

From Windows 7 it is possible to

use two BionicLink PC dongles

connected to one computer

Example

for bilateral

fitting

Alignment and adjustment | Kenevo 3C60 | Prothetik | Global Academy | 12.12.2016

135

Summary of Contents for Kenevo 3C60


















































































































































































































































Search results

Summary of Contents for Kenevo 3C60

Reviews:

Related manuals for Kenevo 3C60

Brands by name

Popular brands

Otto Bock Kenevo 3C60, Introduction Manual

Search results

Summary of Contents for Kenevo 3C60

Reviews:

Related manuals for Kenevo 3C60

Brands by name

Popular brands