Otto Bock Kenevo 3C60 Introduction Manual Download Page 232

Page: 232 / 241

| © Ottobock

Cockpit App

Cockpit App | Kenevo 3C60 | Prosthetic | Global Academy |

232

Adjustments of functions and settings

22.12.2020

•

The user has the possibility to adjust the following
functions and settings in a limited range

•

Functions:

−

Deactivate Bluetooth

•

Settings:

−

Stance flexion resistance (

10 points)

−

Intuitive bicycle ergometer function (On/Off, if
activated in K-Soft)

−

Wheelchair function (On/Off, if activated in K-
Soft)

−

Sitting function (On/Off, if activated in K-Soft)

−

Donning mode (Mode A/B/B+; On/Off, if
activated in K-Soft)

−

Intuitive stance function (Mode C; On/Off, if
activated in K-Soft)

Summary of Contents for Kenevo 3C60


















































































































































































































































Search results

Summary of Contents for Kenevo 3C60

Reviews:

Otto Bock Kenevo 3C60, Introduction Manual, Page: 232 / 241

Search results

Summary of Contents for Kenevo 3C60

Reviews: