13
Chapter 2
Product Specification
and Configuration
S
PECIFICATION
P
RODUCT
S
PECIFICATION
AND
C
ONFIGURATION
C
HAPTER
2
2.1.2
Applicable welding method
This section explains the applicable welding method (shield gas/wire type/welding type) and wire diameter.
Standard specification
WELDING
METHOD
GAS (*)
WIRE MATERIALS
WIRE DIA. [in. (mm)]
TRAVEL SPEED
Penetration
adjustment
DC
CO
2
MILD STEEL
.030 / .035 / .040 / .045
(0.8/0.9/1.0/1.2)
STANDARD (*2)/HIGH
Enable
MAG (20% CO
2
)
(*1-1)
MILD STEEL
.030 / .035 / .040 / .045
(0.8/0.9/1.0/1.2)
STANDARD (*2)/HIGH
Enable
MILD STEEL CORED
.045 / .052 (1.2/1.4)
STANDARD (*2)
Enable
METAL CORED
.045/.052 (1.2/1.4)
STANDARD (*2)
Enable
STAINLESS CORED
.045 (1.2)
STANDARD (*2)
Enable
MIG (2% O
2
)
(*1-2)
STAINLESS STEEL
.030 / .035 / .040 / .045
(0.8/0.9/1.0/1.2)
STANDARD (*2)/HIGH
Enable
STAINLESS FERRITE
.030 / .035 / .040 / .045
(0.8/0.9/1.0/1.2)
STANDARD (*2)/HIGH
Enable
MIG (100% Ar)
(*1-3)
SOFT ALUMINUM
.045 / 1/16 (1.2/1.6)
STANDARD (*2)/HIGH
-
HARD ALUMINUM
.045 / 1/16 (1.2/1.6)
STANDARD (*2)/HIGH
-
DC LOW SPATTER
(*3)
CO
2
MILD STEEL
.030 / .035 / .040 / .045
(0.8/0.9/1.0/1.2)
STANDARD/HIGH
-
MAG (20% CO
2
)
(*1-1)
MILD STEEL
.030 / .035 / .040 / .045
(0.8/0.9/1.0/1.2)
STANDARD/HIGH
-
MIG (2% O
2
)
(*1-2)
STAINLESS STEEL
.030 / .035 / .040 / .045
(0.8/0.9/1.0/1.2)
STANDARD/HIGH
-
STAINLESS FERRITE
.030 / .035 / .040 / .045
(0.8/0.9/1.0/1.2)
STANDARD/HIGH
-
DC TIG
-
-
-
-
-
DC STICK
-
-
-
-
-
*1: Note that the "collective" voltage adjustment may not meet the appropriate condition if a mixing gas other than those with the following
mixing ratios is used.
*1-1: MAG gas: Argon (Ar) 80 % + Carbon dioxide (CO
2
) 20 %
*1-2: MIG gas: Argon (Ar) 98 % + Oxygen (O
2
) 2 %
*1-3: MIG gas: Argon (Ar) 100%
*2: For "STANDARD" mode, the standard mode or extended cable mode (extended mode of power cable) is available.
(
6.7.2.1 F1: Standard/Extended cable mode)
*3: In the welding of DC low spattering, the following devices are necessary for wire feeder and welding torch. For details, refer to the
instruction manual of each device.
•
Wire feeder: CM-743U with voltage detection adaptor kit (K5975V00)
•
Welding torch: BT3500V-30 or BT3510V-30
