OTC Welbee M350 II, Owner'S Manual

Page: 90 / 148

S
ETTING
I
NTERNAL
F
UNCTIONS
W
ELDING
C
ONDITION
C
HAPTER
6
88
• [OFF]: disables the function.
– The wire feed speed is automatically set based on the welding current.
– Even when the welding mode is changed by the GAS menu, the wire feed speed is automatically set based on the
set welding current.
– Each pressing the UNIT CHANGE key, the wire feed speed display and the welding current display switches
alternatively. Switch to the welding current display, and set the welding current in the unit of 1 A.
– Switching to the welding current display can check the wire feed speed automatically set.
– In using the welding power source in the automatic machine mode, refer to the graph in " 6.7.2.4
-
F5: Maximum
external command voltage". (When the internal function F4 (Auto/Semi-auto mode) is used with the setting of
Automatic machine 1 mode)
)WR)([WHUQDORXWSXWWHUPLQDOVHWWLQJ
• Through F25, you can set the functions of OUT-EXT1 (“3” – “4”) on the terminal block for external connection.
• Through F26, you can set the functions of OUT-EXT2 (“5” – “6”) on the terminal block for external connection.
• Through F27, you can set the functions of OUT-EXT3 (“7” – “8”) on the terminal block for external connection.
• Through F28, you can set the functions of OUT-EXT4 (“9” – “10”) on the terminal block for external connection.
Configurable functions are as shown in the below table.
)WR)([WHUQDORXWSXWWHUPLQDOVHWWLQJUHVHUYHG
The external output terminals (OUT-EXT1 to EXT4 on the external output terminal TM4) are used in connection with the
automatic machines of other manufacturers.
)WR)([WHUQDOLQSXWWHUPLQDOVHWWLQJ
Set the function of external input terminals. (when using robot or automatic machines)
• F29: set the function of IN-EXT1 ("5" to "9") on the external connection terminal block TM3.
• F30: set the function of IN-EXT2 ("6" to "9") on the external connection terminal block TM3.
• F31: set the function of IN-EXT3 ("7" to "9") on the external connection terminal block TM3.
• F32: set the function of IN-EXT4 ("8" to "9") on the external connection terminal block TM3.
For the details of external connection terminal block; ( 4.5.2
-
Connection of automatic machine)
The functions allocable to F29 to F32 are as follows:
Setting Function name Explanation
0
−
No function is allocated.
1 to 3
−
No function is allocated in this machine.
4
Alarm Signal of Welding
Monitor
A welding condition error is detected during welding, and the signal is output to the external terminal.
If either of the current/voltage is out of the preset range, the external output terminal with this function
is closed.
Setting Function name Explanation
0 - No function is allocated.
1 Gas valve Causing short circuit between terminals opens the gas valve. (*1)
2 Inching Causing short circuit between terminals starts inching.
3 Retract
When inching operation is performed after short circuit is caused between terminals are short-circuited,
the wire feeding motor reverses to retract the wire. (*2)
4 Start Causing short circuit between terminals starts welding. (torch switch: ON)(*3)
5 Loading welding condition The welding conditions stored on the memory can be read out by combination of signals. (*4), (*5)
*1: When the gas valve is opened by the signal from the external input terminal, the gas valve will not close when welding
completes or according to the timer (2 minutes). In order to stop gas, ensure to open the terminals.
*2: Causing short circuit between the external input terminals before turning on the inching signal. To stop the operation, turn off
the inching signal and then disconnect the external input terminals.
*3: The starting terminal of the feeder receptacle on the front of welding power source becomes deactivated.