Oracle X7-2 Installation Manual Download

Page: 100 / 148

Configure RAID Using the Avago MegaRAID Configuration Utilities

Access the host console locally or through Oracle ILOM.

For instructions, see

“Accessing Oracle ILOM” on page 84

Reset or power on the server.

For example, to reset the server:

■

From the local server,

press the Power button on the front panel of the server for

approximately 1 second to power off the server, and then press the Power button again to

power on the server.

■

From the Oracle ILOM web interface,

select

Host Management

→

Power Control

, and

then select

Reset

from the

Select Action

list box. Click

Save

, and then click

■

From the Oracle ILOM CLI,

type:

reset /System

The power-on self-test (POST) sequence begins.

On the BIOS Setup Utility screen, select the Advanced tab, select Avago

MegaRAID Configuration Utility, and press Enter.

100

Oracle Servers X7-2 and X7-2L Installation Guide • October 2017

Summary of Contents for X7-2





















































































































































Search results

Summary of Contents for X7-2

Reviews:

Related manuals for X7-2

Brands by name

Popular brands

Oracle X7-2, Installation Manual

Search results

Summary of Contents for X7-2

Reviews:

Related manuals for X7-2

Brands by name

Popular brands