Oracle X7-2 Installation Manual Download Page 47

Page: 47 / 148

Install AC Power Cables and Slide-Rails

Place the Rackmounting Template against the front rails, aligning the bottom

edge of the card with the bottom edge of the server, and measure up from the

bottom of the Rackmounting Template.

Mark the mounting holes for the front slide-rails.

Mark the mounting holes for the back slide-rails.

Related Information

■

“Rack Compatibility” on page 41

■

“Install Mounting Brackets on the Server” on page 44

■

“Attach the Slide-Rails” on page 49

Install AC Power Cables and Slide-Rails

Before you install the slide-rails into the rack, install right-angle AC power

cables into the left-side and right-side PDU electrical sockets.

Use the following 2-meter right-angle AC power cable for this procedure:

Installing the Server Into a Rack

Summary of Contents for X7-2





















































































































































Search results

Summary of Contents for X7-2

Reviews:

Related manuals for X7-2

Brands by name

Popular brands

Oracle X7-2, Installation Manual

Search results

Summary of Contents for X7-2

Reviews:

Related manuals for X7-2

Brands by name

Popular brands