Oracle X7-2 Installation Manual Download

Page: 140 / 148

Preparation Checklists

Rackmount Considerations

Yes

N/A Comment

Is the distance between the front and back mounting

planes between a minimum of 610 mm and a maximum

915 mm (24 inches to 36 inches)?

Is the clearance depth in the front of the front mounting

plane (distance to the front cabinet door) at least 25.4

mm (1 inch)?

Does the target rack meet the following minimum load

capacity:

■ 19 kg/rack unit
■ 785 kg total

Is the rack a four-post rack (mounting at both front and

back)?

Two-post racks are not compatible.

Do the horizontal opening and unit vertical pitch of the

rack conform to ANSI/EIA 310-D-1992 or IEC 60297

standards?

Does the rack have RETMA rail support?

Does the rack support Oracle cable management arms

(CMAs)?

Does the rack support installation of Oracle vented and

solid filler panels?

Is there sufficient space for cable harnesses and the

power distribution units (PDUs) in the rack, if required?
Can a label with the server serial number be printed and

attached to the target rack?

Did you label the network cables that will connect to

the server?

Does the rack support installation of standard Oracle

PDUs?

If not, then complete this checklist.

Can the customer provide an equivalent pair of PDUs?

Can the customer provide two PDUs with capacity of

110kVA per PDU?

Can the customer provide a single PDU and its circuits

to support the power requirements in case a PDU fails?

Can the customer ensure power loads are evenly

distributed across all circuits of a single PDU?

140

Oracle Servers X7-2 and X7-2L Installation Guide • October 2017

Summary of Contents for X7-2





















































































































































Search results

Summary of Contents for X7-2

Reviews:

Related manuals for X7-2

Brands by name

Popular brands

Oracle X7-2, Installation Manual

Search results

Summary of Contents for X7-2

Reviews:

Related manuals for X7-2

Brands by name

Popular brands