Oracle X7-2 Installation Manual Download

Page: 119 / 148

Controlling System Power

This section describes how to power on, power off, and reset the server.

■

“Powering the Host On and Off” on page 119

■

“Resetting the Server” on page 122

Related Information

■

“Installation Procedure Overview” on page 11

■

Oracle Integrated Lights Out Manager (ILOM) Documentation Library at:

http://www.

oracle.com/goto/ilom/docs

Powering the Host On and Off

Your server has three power modes (states): power off, standby power, and main power.

Power

State

Description

Indicators

Action

Power off

The server is completely

powered off when the

AC power cords are

disconnected.

All indicators are off.

The server is disconnected

from all power sources.

Disconnect power cords to completely

remove power.

Caution - Electrical Hazard.

Equipment

damage. Do not disconnect power cords

when the system is in Main power mode.

Standby

power

When the server is in

Standby power mode,

the service processor is

powered on but the host is

powered off.

The green System OK

indicator blinks slowly.

The green SP OK indicator

is steady on.

If the server is completely powered off,

plug in the power cords to apply Standby

power.

If the server is in Main power mode, use

Oracle ILOM or the Power button to

remove host power.

You can power the host off gracefully, or

immediately.

Controlling System Power

119

Summary of Contents for X7-2





















































































































































Search results

Summary of Contents for X7-2

Reviews:

Related manuals for X7-2

Brands by name

Popular brands

Oracle X7-2, Installation Manual

Search results

Summary of Contents for X7-2

Reviews:

Related manuals for X7-2

Brands by name

Popular brands