Oracle X7-2 Installation Manual Download Page 72

Page: 72 / 148

X7-2 Back Panel Connectors and Ports

■

Ethernet ports:

■ ■

The Ethernet ports, labeled NET 0, NET 1, and NET 2, connect the server to the

network.

■

The Ethernet interfaces operate at 100 Mbps, 1000 Mbps, and 10,000 Mbps.

■

USB Ports:

You can connect and disconnect USB cables and peripheral devices while the

server is running without affecting server operations.

■

AC power cables:

Two power supply connectors, one for each power supply.

X7-2 Back Panel Connectors and Ports

The following figure shows the locations of cable connectors and ports on the back of the

Oracle Server X7-2 and the cables and devices that you connect to them.

No.

Cable Port or Expansion Slot

Description

Power supply 0 input power

Power supply 1 input power

The server has two power supply connectors,

one for each power supply.

Do not attach power cables to the power

supplies until you finish connecting the data

cables to the server. The server goes into

Oracle Servers X7-2 and X7-2L Installation Guide • October 2017

Summary of Contents for X7-2





















































































































































Search results

Summary of Contents for X7-2

Reviews:

Related manuals for X7-2

Brands by name

Popular brands

Oracle X7-2, Installation Manual

Search results

Summary of Contents for X7-2

Reviews:

Related manuals for X7-2

Brands by name

Popular brands