Oracle X7-2 Installation Manual Download Page 39

Page: 39 / 148

Installing the Server Into a Rack

This section describes how to install the server into a rack using the slide-rail assembly in the

Rackmount Kit. Figures for the rackmounting procedures depict Oracle Server X7-2L. The

procedures are the same for the Oracle Server X7-2.

Note -

In this guide, the term "rack" means either an open rack or a closed cabinet.

■

“Installation Prerequisites” on page 39

■

“Safety Precautions” on page 39

■

“ESD Precautions” on page 41

■

“Rack Compatibility” on page 41

■

“Rackmount Kit Contents” on page 43

■

“Rackmounting the Server” on page 44

Related Information

■

“Installation Procedure” on page 11

■

“Preparing for Server Installation” on page 13

Installation Prerequisites

Before you start the rackmount procedures, ensure that that your site meets the required

electrical and environmental requirements. See

“Preparing for Server Installation” on page 13

Safety Precautions

This section describes safety precautions you must follow when installing the server into a rack.

Installing the Server Into a Rack

Summary of Contents for X7-2





















































































































































Search results

Summary of Contents for X7-2

Reviews:

Related manuals for X7-2

Brands by name

Popular brands

Oracle X7-2, Installation Manual

Search results

Summary of Contents for X7-2

Reviews:

Related manuals for X7-2

Brands by name

Popular brands