Oracle X7-2 Installation Manual Download Page 107

Page: 107 / 148

Configure RAID Using the Avago MegaRAID Configuration Utilities

13.

Select

Confirm

, select

Enabled

, and press

Enter

14.

To save your new boot configuration, select

Yes

15.

To exit the Avago MegaRAID Utility, press the

ESC

Rapid Storage Technology Enterprise (RSTe)

You can create and manage RAID arrays on the Oracle Servers X7-2 and X7-2L SATA M.2

(SSDs) using Intel Rapid Storage Technology Enterprise (RSTe) which provides the following

benefits:

■

Additional protection from data loss.

■

Data is protected against a drive failure when you configure your system for RAID level 1

(mirror).

■

Additional advantage of allowing an operating system to install directly to the RAID

volume.

■

BIOS exports the volumes as a target device to the operating system installer, streamlining

the OS installation.

■

The OS uses the system CPUs to manage and configure the RAID volumes.

Configuring Storage Drives for Operating System Installation

107

Summary of Contents for X7-2





















































































































































Search results

Summary of Contents for X7-2

Reviews:

Related manuals for X7-2

Brands by name

Popular brands

Oracle X7-2, Installation Manual

Search results

Summary of Contents for X7-2

Reviews:

Related manuals for X7-2

Brands by name

Popular brands