manualshive.com logo in svg

Oracle SPARC T8-2, Service Manual

Share
Download
Oracle SPARC T8-2 Service Manual Download Page 97

Replace a Faulty DIMM

■

“Remove a DIMM” on page 100

■

“Server Top View” on page 16

Replace a Faulty DIMM

Caution - 

This procedure requires handling components that are sensitive to ESD. 

Follow

antistatic practices

 to avoid damage or component failure.

Customers can perform this procedure, but the system must first be completely powered down

and all power cords unplugged. See 

“Component Service Categories” on page 48

 for more

information about cold-service procedures.

Perform this procedure to replace a faulty DIMM on the motherboard or a memory riser.

1.

Identify the faulty DIMM

 to be removed using the ILOM 

show faulty

 command.

2.

Prepare the system for service

.

3.

Unplug the power cords

.

4.

Remove the appropriate memory riser

.

To remove a DIMM from the motherboard, you must remove the memory riser above that

DIMM to enable access.

5.

Locate the faulty DIMM

 on the motherboard or memory riser using the DIMM

fault LEDs.

6.

Remove the faulty DIMM

.

7.

Ensure the replacement DIMM has the 

same rank classification

 as the faulty

DIMM.

8.

Install the replacement DIMM

.

9.

Install the memory riser

 that you removed.

10.

Return the server to operation

.

11.

Enable and verify

 the replacement DIMM.

Servicing Memory Risers and DIMMs

97

Summary of Contents for SPARC T8-2





























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands