Oracle SPARC T8-2 Service Manual Download Page 178

Page: 178 / 188

DMP

DMP

Dynamic multipathing.

DTE

Data terminal equipment.

EIA

Electronics Industries Alliance.

ESD

Electrostatic discharge.

eUSB drive

Embedded universal serial bus drive.

FRU

Field-replaceable unit.

HBA

Host bus adapter.

host

The part of the server or server module with the CPU and other hardware that runs the Oracle

Solaris OS and other applications. The term

host

is used to distinguish the primary computer

from the SP.

See

hot-pluggable

Describes a component that can be replaced with power applied, but the component must be

prepared for removal.

hot-

swappable

Describes a component that can be replaced with power applied, and no preparation is required.

ID PROM

Chip that contains system information for the server or server module.

Internet Protocol.

178

SPARC T8-2 Server Service Manual • June 2019

Summary of Contents for SPARC T8-2





























































































































































































Search results

Summary of Contents for SPARC T8-2

Reviews:

Related manuals for SPARC T8-2

Brands by name

Popular brands

Oracle SPARC T8-2, Service Manual

Search results

Summary of Contents for SPARC T8-2

Reviews:

Related manuals for SPARC T8-2

Brands by name

Popular brands