manualshive.com logo in svg

Oracle SPARC T8-2, Service Manual

Share
Download
Oracle SPARC T8-2 Service Manual Download Page 173

Return the Server to the Normal Operating Position

Return the Server to the Normal Operating Position

Caution - 

The chassis is heavy. To avoid personal injury, use two people to lift the server and

set it in the rack.

1.

Release the slide rails from the fully extended position by pushing the release

tabs on the side of each rail.

2.

While pushing on the release tabs, slowly push the server into the rack.

Ensure that the cables do not get in the way.

3.

Reconnect the cables to the rear of the server.

If the CMA is in the way, disconnect the left CMA release and swing the CMA open. See

“Release the CMA” on page 57

.

4.

Reconnect the CMA.

Swing the CMA closed and latch it to the left rack rail. See 

Server Installation

 for more detail

about attaching the CMA.

Returning the Server to Operation

173

Summary of Contents for SPARC T8-2





























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands