Oracle SPARC T8-2 Service Manual Download Page 129

Page: 129 / 188

Servicing the SPM

These topics describe how to service the SPM module.

■

“SPM Firmware and Configuration” on page 129

■

“Remove the SPM” on page 130

■

“Install the SPM” on page 131

■

“Verify the SPM” on page 134

SPM Firmware and Configuration

System firmware consists of two components, an SPM component and a host component. The

SPM firmware component is located on the SPM, and the host component is located on the

motherboard. For the server to operate correctly, the firmware in these two components must be

compatible.

When replacing the SPM, you must restore the configuration settings maintained in the SPM.

Before replacing the SPM, save the configuration using the Oracle ILOM backup utility. Refer

to the Oracle ILOM documentation for instructions on backing up and restoring the Oracle

ILOM configuration.

After replacing the SPM, the new SPM firmware component and the existing host

firmware component must be consistent with each other. To ensure that the firmware is

compatible throughout the server, load new system firmware as described in

“Install the

SPM” on page 131

Related Information

■

Oracle ILOM documentation in

http://www.oracle.com/goto/ilom/docs

■

“Servicing the Motherboard” on page 147

■

“Remove the SPM” on page 130

■

“Install the SPM” on page 131

Servicing the SPM

129

Summary of Contents for SPARC T8-2





























































































































































































Search results

Summary of Contents for SPARC T8-2

Reviews:

Brands by name

Popular brands

Oracle SPARC T8-2, Service Manual

Search results

Summary of Contents for SPARC T8-2

Reviews:

Brands by name

Popular brands