manualshive.com logo in svg

Oracle SPARC T8-2, Service Manual

Share
Download
Oracle SPARC T8-2 Service Manual Download Page 55

Prevent ESD Damage

Prevent ESD Damage

Many components housed within the chassis can be damaged by ESD. To protect these

components from damage, perform the following steps before opening the chassis for service.

1.

Prepare an antistatic surface to set parts on during the removal or installation

process.

Place ESD-sensitive components such as the printed circuit boards on an antistatic mat. The

following items can be used as an antistatic mat:

■

Antistatic bag used to wrap a replacement part

■

ESD mat

■

Disposable ESD mat (shipped with some replacement parts or optional components)

2.

Attach an antistatic wrist strap.

When servicing or removing server components, attach an antistatic strap to your wrist and then

to a metal area on the chassis.
See 

“Safety Information” on page 45

.

Related Information

■

“Safety Information” on page 45

Extend the Server to the Service Position

You can service the following components with the server in the service position:

■

Drives

■

Power supplies

■

Fans

■

Fan modules

■

Memory risers

■

DIMMs

■

PCIe cards

■

SPM card

■

Battery

■

eUSB drive

Preparing for Service

55

Summary of Contents for SPARC T8-2





























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands