Oracle SPARC T8-2 Service Manual Download Page 13

Page: 13 / 188

Identifying Components

These topics identify key components of the server, including major boards and internal system

cables, as well as front and rear panel features.

For system overview information, see

“Understanding the Server” in

SPARC T8-2 Server

Installation Guide

■

“Front Panel Components (Service)” on page 13

■

“Rear Panel Components (Service)” on page 15

■

“Internal System Cables” on page 15

■

“Server Top View” on page 16

■

“Internal Component Locations” on page 17

■

“Motherboard Component Locations” on page 19

■

“I/O Component Locations” on page 21

■

“Power Distribution and Fan Module Component Locations” on page 22

■

“Server Block Diagram” on page 23

Related Information

■

“Detecting and Managing Faults” on page 27

■

“Preparing for Service” on page 45

Front Panel Components (Service)

The following figure shows the layout of the server front panel, including the power and server

locate buttons and the various status and fault LEDs.

Note -

The front panel also provides access to internal drives, the removable media drive (if

equipped), and the two front USB ports.

Identifying Components

Summary of Contents for SPARC T8-2





























































































































































































Search results

Summary of Contents for SPARC T8-2

Reviews:

Related manuals for SPARC T8-2

Brands by name

Popular brands

Oracle SPARC T8-2, Service Manual

Search results

Summary of Contents for SPARC T8-2

Reviews:

Related manuals for SPARC T8-2

Brands by name

Popular brands