Oracle SPARC T8-2 Service Manual Download Page 167

Page: 167 / 188

Install the PS Backplane

Lift the PS backplane out of the chassis.

Slide the PS backplane back towards the power supplies to remove the PS

backplane mount from underneath the motherboard.

Tilt the PS backplane to remove it from the power supply shroud.

Disconnect the AC cables from the PS backplane.

Tilt the PS backplane to access the cable connectors.

10.

Install a new PS backplane.

See

“Install the PS Backplane” on page 167

Related Information

■

“Install the PS Backplane” on page 167

Install the PS Backplane

This is a cold-service procedure that must be performed by qualified service personnel. Power

down the server completely before performing this procedure.

Caution -

This procedure requires that you handle components that are sensitive to ESD which

can cause server components to fail.

Unpack the replacement PS backplane and place it on an antistatic mat.

Hold the PS backplane at the end of the power supply cage at an angle, and

connect the AC cables to the AC connectors on the PS backplane.

Ensure that each AC cable is connected to the appropriate connector. You must connect the AC

cable on the right to the AC connector on the right, and connect the AC cable on the left to the

AC connector on the left.

Insert the PS backplane into position (panel 1).

Servicing the PS Backplane

167

Summary of Contents for SPARC T8-2





























































































































































































Search results

Summary of Contents for SPARC T8-2

Reviews:

Related manuals for SPARC T8-2

Brands by name

Popular brands

Oracle SPARC T8-2, Service Manual

Search results

Summary of Contents for SPARC T8-2

Reviews:

Related manuals for SPARC T8-2

Brands by name

Popular brands