Oracle SPARC T8-2 Service Manual Download Page 46

Page: 46 / 188

Safety Information

■

Follow all cautions and instructions marked on the equipment and described in the

SPARC

T8-2 Safety and Compliance Guide

■

Ensure that the voltage and frequency of your power source match the voltage and

frequency inscribed on the equipment's electrical rating label.

■

Follow the ESD safety practices as described in this section.

Safety Symbols

Note the meanings of the following symbols that might appear in this document:

Caution -

There is a risk of personal injury or equipment damage. To avoid personal injury and

equipment damage, follow the instructions.

Caution -

Hot surface. Avoid contact. Surfaces are hot and might cause personal injury if

touched.

Caution -

Hazardous voltages are present. To reduce the risk of electric shock and danger to

personal health, follow the instructions.

ESD Measures

ESD sensitive devices, such as the cards, drives, and DIMMS, require special handling.

Caution -

Circuit boards and drives contain electronic components that are extremely

sensitive to static electricity. Ordinary amounts of static electricity from clothing or the work

environment can destroy the components located on these boards. Do not touch the components

along their connector edges.

Caution -

You must disconnect all power supplies before servicing any of the components that

are inside the chassis.

Antistatic Wrist Strap Use

Wear an antistatic wrist strap and use an antistatic mat when handling components such as drive

assemblies, circuit boards, or PCIe cards. When servicing or removing server components,

SPARC T8-2 Server Service Manual • June 2019

Summary of Contents for SPARC T8-2





























































































































































































Search results

Summary of Contents for SPARC T8-2

Reviews:

Related manuals for SPARC T8-2

Brands by name

Popular brands

Oracle SPARC T8-2, Service Manual

Search results

Summary of Contents for SPARC T8-2

Reviews:

Related manuals for SPARC T8-2

Brands by name

Popular brands