Oracle SPARC T8-2 Service Manual Download Page 54

Page: 54 / 188

Disconnect Power Cords

Disconnect Power Cords

Remove the power cords from the server only after powering off the server.

Unplug all power cords from the server.

Caution -

Because 3.3V standby power is always present in the server, you must unplug the

power cords before accessing any cold-serviceable components.

Related Information

■

“Power Off the Server (Oracle ILOM)” on page 52

■

“Power Off the Server (Server Power Button - Graceful)” on page 53

■

“Power Off the Server (Emergency Shutdown)” on page 53

■

“Rear Panel Components (Service)” on page 15

Related Information

■

“Safety Information” on page 45

Accessing Server Components

These topics explain how to access components on the outside and the inside of the server.

Perform these tasks in this order, as needed.

■

“Prevent ESD Damage” on page 55

■

“Extend the Server to the Service Position” on page 55

■

“Release the CMA” on page 57

■

“Remove the Server From the Rack” on page 59

■

“Remove the Top Cover” on page 60

Related Information

■

“Safety Information” on page 45

SPARC T8-2 Server Service Manual • June 2019

Summary of Contents for SPARC T8-2





























































































































































































Search results

Summary of Contents for SPARC T8-2

Reviews:

Related manuals for SPARC T8-2

Brands by name

Popular brands

Oracle SPARC T8-2, Service Manual

Search results

Summary of Contents for SPARC T8-2

Reviews:

Related manuals for SPARC T8-2

Brands by name

Popular brands