Oracle SPARC T8-2 Service Manual Download Page 150

Page: 150 / 188

Remove the Motherboard

Lift the cover out of the chassis.

The two cables are now exposed. Be prepared to move those cables out of the way when

you lift the motherboard.

11.

Remove the four bus bar screws that secure the motherboard to the PS

backplane.

See

“Remove the PS Backplane” on page 165

12.

Position the drive end of the cables off to the side using the tab on the top of the

plastic power supply cover.

13.

Remove the motherboard.

Loosen the captive screw (in the corner near the fans) that secures the

motherboard to the chassis (panel 1).

Grasp the handle on the motherboard and slide it toward the front of the

chassis (panel 2).

150

SPARC T8-2 Server Service Manual • June 2019

Summary of Contents for SPARC T8-2





























































































































































































Search results

Summary of Contents for SPARC T8-2

Reviews:

Related manuals for SPARC T8-2

Brands by name

Popular brands

Oracle SPARC T8-2, Service Manual

Search results

Summary of Contents for SPARC T8-2

Reviews:

Related manuals for SPARC T8-2

Brands by name

Popular brands