manualshive.com logo in svg

Oracle SPARC T8-2, Service Manual

Share
Download
Oracle SPARC T8-2 Service Manual Download Page 91

Memory Riser and DIMM FRU Names

The following DIMMs are supported:

DIMM Capacity

DRAM Density

Rank Classification

Label

16 Gbyte

4 Gbit

Dual-rank x4

2Rx4

32 Gbyte

4 Gbit

Quad-rank x4

4Rx4

32 Gbyte

8 Gbit

Dual-rank x4

2Rx4

64 Gbyte

8 Gbit

Quad-rank x4

4Rx4

Memory Riser and DIMM FRU Names

This server includes eight memory risers. Four memory risers are associated with each CMP in

the server. A label is next to each memory riser that shows the number of the CMP and of the

riser. Four DIMM slots are on each memory riser.

Note - 

The server fails to boot unless all memory riser slots are populated. For more

information about memory riser configuration, see 

“Memory Riser and DIMM

Configuration” on page 89

.

Servicing Memory Risers and DIMMs

91

Summary of Contents for SPARC T8-2





























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands