manualshive.com logo in svg

Oracle SPARC T8-2, Service Manual

Share
Download
Oracle SPARC T8-2 Service Manual Download Page 63

Servicing Drives

The server provides six 2.5-inch drive bays, accessible through the front panel. See 

“Front

Panel Components (Service)” on page 13

. Drives can be removed and installed while the server

is running. This feature, referred to as being 

hot-serviceable

, depends on how the drives are

configured.

The server supports traditional, disk-based storage devices, Flash SSDs, which are diskless

storage devices based on solid-state memory, and SFF-8639 NVMe PCIe SSDs, which are

diskless storage devices based on solid-state memory using the NVMe software interface.

NVMe drives are supported in the top four drive slots, while other drives are supported in any

slot. Any of these drives can be a boot device.

Note - 

The terms “drive” and “HDD” are used in a generic sense to refer to internal storage

devices.

These topics explain how to service drives.

■

“Drive LEDs” on page 64

■

“Determine Which Drive Is Faulty” on page 65

■

“Remove a Drive” on page 65

■

“Remove a Drive Filler” on page 69

■

“Install a Drive” on page 70

■

“Install a Drive Filler” on page 72

■

“Verify a Drive” on page 73

Related Information

■

“Component Service Categories” on page 48

■

“Front Panel Components (Service)” on page 13

Servicing Drives

63

Summary of Contents for SPARC T8-2





























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands