manualshive.com logo in svg

Oracle SPARC T8-2, Service Manual

Share
Download
Oracle SPARC T8-2 Service Manual Download Page 155

Reactivate RAID Volumes

23.

Power on the server.

See 

“Power On the Server (Oracle ILOM)” on page 174

 or 

“Power On the Server (System

Power Button)” on page 175

.

24.

(Optional) Transfer the serial number and product number to the FRUID of the

new motherboard.

If the replacement motherboard must have the same serial number as the server prior to

servicing, trained service personnel must take this action in a special service mode.

Related Information

■

Oracle ILOM documentation

■

“Remove the Motherboard” on page 147

■

“Reactivate RAID Volumes” on page 155

■

“Verify the Motherboard” on page 158

Reactivate RAID Volumes

Perform this task only if your server had RAID volumes prior to replacing the motherboard.

1.

Prior to powering on the server, log in to the SPM.

Refer to 

Servers Administration

 for instructions.

2.

At the Oracle ILOM prompt, disable 

auto-boot

 so that the server will not boot the

OS when the server powers on.

-> 

set /HOST/bootmode script="setenv auto-boot? false"

3.

Power on the server.

See 

“Power On the Server (Oracle ILOM)” on page 174

 or 

“Power On the Server (System

Power Button)” on page 175

.

4.

At the OpenBoot prompt, list the device paths on the server.

ok 

show-devs

...
/pci@400/pci@2/pci@0/pci@e/scsi@0
...

You can also use the 

devalias

 command to locate device paths specific to your server.

Servicing the Motherboard

155

Summary of Contents for SPARC T8-2





























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands