OmniCell ERB Installation And Service Manual Download Page 21

Page: 21 / 112

External Return Bin Installation and Service Guide/

67-2038 Rev D

Installation Instructions

2-11

Installation on G3 Cabinets

2. Insert the longer end of the new transport handle into the left slot followed through with the

other end into the right slot.

Figure 2-27.

Installing the new transport handle

3. Secure the handle with the two screws removed in

step 1

. Note the threaded hole orientation.

4. Place the External Return Bin on a flat clean surface, before opening the access door with both

keys. Use

key

#2204 to unlock the access door and

key

#2202 to override the solenoid.

Figure 2-28.

Opening the access door

5. Align the two drilled holes on the transport handle to the two drilled holes inside the ERB.

Secure the handle with two

#8 hex nuts

Figure 2-29.

Screw hole locations

6. Close and lock the access door

Summary of Contents for ERB

















































































































Search results

Summary of Contents for ERB

Reviews:

Related manuals for ERB

Brands by name

Popular brands

OmniCell ERB, Installation And Service Manual

Search results

Summary of Contents for ERB

Reviews:

Related manuals for ERB

Brands by name

Popular brands