OmniCell ERB Installation And Service Manual Download Page 13

Page: 13 / 112

External Return Bin Installation and Service Guide/

67-2038 Rev D

Installation Instructions

2-3

Setup

c. Loosen, but do not remove, the two nuts on either side of the

PCB/solenoid plate

with a

5/16" nut driver.

Figure 2-5.

Loosening the nuts on both sides of the PCB/solenoid plate

d. Maneuver the PCB/solenoid mount around the sheet metal tabs and nuts. Remove the

lower rim first.

Figure 2-6.

Removing the PCB/solenoid mount

Under the PCB/solenoid mount is an internal cover to reduce the radiated emissions level.

6. Remove the

RFI cover

that is under the PCB/solenoid mount.

a. Loosen the two hex nuts on either side of the internal cover using a 5/16” nut driver or

socket.

Figure 2-7.

Loosening hex nuts

Summary of Contents for ERB

















































































































Search results

Summary of Contents for ERB

Reviews:

Related manuals for ERB

Brands by name

Popular brands

OmniCell ERB, Installation And Service Manual

Search results

Summary of Contents for ERB

Reviews:

Related manuals for ERB

Brands by name

Popular brands