OmniCell ERB Installation And Service Manual Download Page 11

Page: 11 / 112

External Return Bin Installation and Service Guide/

67-2038 Rev D

2-1

Installation Instructions

Setup

Before installing the ERB, change the cabling configuration if necessary, and perform cabinet
preparation.

Cable Assembly Configuration

If the ERB is to be installed on the right side of the cabinet, skip to

“Cabinet Preparation”

page 2-10.

If the ERB is to be installed on the left side of the cabinet, continue in this section to change the
cabling configuration.

1. Place the ERB on a flat clean surface.

2. Open the access door using both keys.

Key

#2204 unlocks the access door.

Key

#2202 overrides

the solenoid.

Figure 2-1.

Unlock the access door

Important:

The ERB cable assembly

is configured to be installed on the right side of cabinets with the

cables leading to the back. If the ERB is to be installed on the left side of the cabinet, the cable assembly
must be switched to the left side. This avoids having to bend cables back across the ERB to reach the
back of the cabinet.

Summary of Contents for ERB

















































































































Search results

Summary of Contents for ERB

Reviews:

Related manuals for ERB

Brands by name

Popular brands

OmniCell ERB, Installation And Service Manual

Search results

Summary of Contents for ERB

Reviews:

Related manuals for ERB

Brands by name

Popular brands