OmniCell ERB Installation And Service Manual Download Page 56

Page: 56 / 112

2-46

Installation Instructions

Installation on G4 Cabinets

External Return Bin Installation and Service Guide

/67-2038 Rev D

Cabling for the OmniTT G4

If possible the ERB should be installed on the left side (monitor side) of the OmniTT G4, to
maximize strain relief.

Cabling for the ERB on the Left Side of the Cabinet

1. Reconfigure the cabling in the ERB as described in

“Cable Assembly Configuration”

page 2-1.

2. Remove the lid from the cabinet.

a. Use the #2378

cam lock key to unlock the lid.

Figure 2-115.

Unlocking the lid

b. Rotate the lid up, and lift it from the hooks that hold it.

Figure 2-116.

Removing the lid

c. Place the lid aside.

Note:

Although it is possible to prop the cover open with the kick stand, removing it provides better

access.

Summary of Contents for ERB

















































































































Search results

Summary of Contents for ERB

Reviews:

Related manuals for ERB

Brands by name

Popular brands

OmniCell ERB, Installation And Service Manual

Search results

Summary of Contents for ERB

Reviews:

Related manuals for ERB

Brands by name

Popular brands