OmniCell ERB Installation And Service Manual Download Page 87

Page: 87 / 112

External Return Bin Installation and Service Guide/

67-2038 Rev D

Installation Instructions

2-77

Implementation

Implementation

Power Up

1. Connect the power cable to the cabinet.

2. Turn on the cabinet.

Configuration and Test

The following configuration option is listed in the Hardware configuration menu on the Color
Touch screen.

1. Set this option to

Yes

to use the ERB.

2. Test the ERB.

a. Perform the return function in the application.

b. Open and close the ERB door.

c. Check the Color Touch screen for error or status messages.

3. Give the pharmacist both ERB keys.

Menu Name

External Return Bin

Description

Indicates that an External Return Bin is present and in use. When set to Yes, all other return bins will be ignored.

Values

Yes/No

Default

Summary of Contents for ERB

















































































































Search results

Summary of Contents for ERB

Reviews:

Related manuals for ERB

Brands by name

Popular brands

OmniCell ERB, Installation And Service Manual

Search results

Summary of Contents for ERB

Reviews:

Related manuals for ERB

Brands by name

Popular brands