OmniCell ERB Installation And Service Manual Download Page 97

Page: 97 / 112

External Return Bin Installation and Service Guide/

67-2038 Rev D

Service

3-9

Access Door

Access Door

The access door solenoid may be difficult to reach inside the ERB unit. The solenoid is located
inside the return door, which makes it hard to visually see the parts.

1. Open the access door with

keys

#2204 (unlocks access door) and #2202 (overrides access door

solenoid).

2. Open the return door by pushing the pawl of the solenoid to the left and lifting the handle.

Figure 3-21.

Pushing the pawl and opening the return door

3. Remove the three

4-40 x 1/4

”

FH undercut Torx screws

from the underside of the LED mount

bracket.

Figure 3-22.

Removing the LED mount bracket screws

4. Remove the two

#4 hex nuts

securing the bracket LED mount from the inside of the ERB with

a 1/4" nut driver or socket.

Figure 3-23.

Hex nut locations

LED brack

et moun

t location

Summary of Contents for ERB

















































































































Search results

Summary of Contents for ERB

Reviews:

Related manuals for ERB

Brands by name

Popular brands

OmniCell ERB, Installation And Service Manual

Search results

Summary of Contents for ERB

Reviews:

Related manuals for ERB

Brands by name

Popular brands