OmniCell ERB Installation And Service Manual Download Page 91

Page: 91 / 112

External Return Bin Installation and Service Guide/

67-2038 Rev D

Service

3-3

Return Door Handle

9. Insert and tighten the 6-32 PH Torx screws.

10. Maneuver the metal mount back into position.

11. Tighten the two nuts on either side of the plate.

12. Close the return door.

13. Lock up the ERB.

Return Door Handle

1. Open the access door with

keys

#2204 (unlocks access door) and #2202 (overrides access door

solenoid).

2. Open the return door by pushing the pawl of the solenoid to the left and lifting the handle.

Figure 3-5.

Pushing the pawl; return door handle

3. Remove the two

M4x6mm FH Phillips screws

securing the handle spacer with a Phillips

screwdriver #2, then set the old handle aside.

Figure 3-6.

Handle screw locations

4. Set the new

return door handle

in place.

5. Secure the handle with the two Phillips screws.

6. Close the return door.

7. Lock up the ERB.

Note:

The counter sink on the handle spacer must be aligned with the flat head screws for the lid to

close properly.

Summary of Contents for ERB

















































































































Search results

Summary of Contents for ERB

Reviews:

Related manuals for ERB

Brands by name

Popular brands

OmniCell ERB, Installation And Service Manual

Search results

Summary of Contents for ERB

Reviews:

Related manuals for ERB

Brands by name

Popular brands