OmniCell ERB Installation And Service Manual Download Page 68 | Manualshive

Page: 68 / 112

background image

2-58

Installation Instructions

Installation on G4 Cabinets

External Return Bin Installation and Service Guide

/67-2038 Rev D

© 2011 Omnicell, Inc.

Installing on the Anesthesia Workstation (AWS G4)

The ERB on the AWS G4 is installed on the right side. The bracket is attached to

adjustable

mounting bars

.

The AWS G4 has two installation heights. The procedure for attaching the ERB is slightly different
for each. Typically, the ERB is installed in the upper position. It is installed in the lower position if
the AWS has an optional worksurface installed.

Attaching the ERB in the Upper Position

1. Adjust the upper mounting bar on the right side of the AWS G4.

The top bar should be at least 4-1/2 inches down from the bottom edge of the worksurface.

a. Use a 1/4” Allen key to loosen the

5/16” set screw

on both ends of the bar.

b. Slide the bar into position.

c. Retighten the screws.

2. Attach the

to the upper bar using two

8/32 flat head screws

Figure 2-140.

ERB bracket attached to upper mounting bar at height limit

3. Move the lower bar into position.

4. Attach the bracket to the lower bar using two

8/32 flat head screws

.

Figure 2-141.

ERB Bracket mounting screw positions

Top of mounting bar

Worksurface (bottom edge)

«
...
66
67
68
69
70
...
»

Summary of Contents for ERB

















































































































Reviews:

No comments

Related manuals for ERB

Brand: JB Systems Pages: 12

Brand: GE Pages: 212

Brand: Gamry Instruments Pages: 69

Brand: Gamry Instruments Pages: 30

Brand: Gamry Instruments Pages: 88

Brand: Rayger Pages: 2

Brand: laerdal Pages: 8

Brand: LAHTI PRO Pages: 16

Brand: laerdal Pages: 32

Brand: laerdal Pages: 32

Brand: laerdal Pages: 8

Brand: Parker Pages: 24

Brand: York International Pages: 16

Brand: X-10 Pages: 12

Brand: Equinox Systems Pages: 8

Brand: RAM Pages: 4

Clinician Premiere Series

Brand: OAKWORKS Pages: 29

Brand: Aeware Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands