9 – 10
Ukon
č
ení režimu testování
Režim testování se ukon
č
í, není-li po dobu ca. 30 s, stisknuto
žádné tla
č
ítko.
Svítí-li všechny LED, je režim testování ukon
č
en po ca. 1 s.
9.2.3.2 Modul ZSI
Funkce
Kombinace jisti
č
e s modulem ZSI (
č
asov
ě
zkrácené
ř
ízení selektiv-
ity) umož
ň
uje v rozvodných za
ř
ízeních s více úrovn
ě
mi jišt
ě
ní
lokalizovat místo zkratu.
Za tímto ú
č
elem se všechny jisti
č
e vzájemn
ě
propojí prost
ř
ed-
nictvím svých modul
ů
ZSI.
P
ř
i zkratu v rozvodu se každý jisti
č
, kterým protéká zkratový proud
ptá jisti
č
e na nižší úrovni, zjistil-li také zkrat. Vypíná jen jisti
č
na
úrovni, která je ve sm
ě
ru toku energie nejblíže místu zkratu. P
ř
itom
je vy
ř
azeno zpožd
ě
ní vypnutí p
ř
i zkratu (je-li nastaveno). Vypnutí
nastane až po uplynutí 50 ms, obvykle b
ě
hem 80 až 90 ms.
Modul ZSI jisti
čů
SENTRON WL jsou funk
č
n
ě
kompatibilní s moduly
ZSI jisti
čů
3WN, 3WS a SENTRON VL.
Montáž
→
(strana 9-99)
Propojení
→
Montáž propojení (strana 9-99)
Na jisti
č
lze p
ř
ipojit jej jeden modul ZSI.
Je-li modul ZSI v konfiguraci s dalšími moduly
Cubicle
BUS, musí
se modul ZSI p
ř
ipojit jako první p
ř
ímo na modul COM15 resp. na
konektor pomocných obvod
ů
X8.
Quitting the test mode
Do not press the "TEST" button for about 30 s.
If all LED's are on, the test mode is already quitted after about 1 s.
9.2.3.2 ZSI-module
Function
If the circuit-breaker is combined with a ZSI-module, a short-circuit
occurring in systems with several grading levels can be localised
precisely.
For this purpose, all circuit-breakers are interconnected through
their ZSI-modules.
In case of short-circuit, each circuit-breaker affected by the short-
circuit current interrogates its downstream circuit-breaker to
determine fault presence at this downstream level. In the direction
of the energy flow, only the circuit-breaker nearest to the short-
circuit. A possible time delay setting for the short-circuit tripping is
deactivated. However, tripping will not take place until 50 ms later at
the earliest, as a rule it will take 80 ... 90 ms.
The ZSI-module of the circuit-breaker SENTRON WL is function-
compatible with the ZSI-module of the circuit-breakers 3WN and
3WS as well as the MCCB SENTRON VL.
Installation
→
(page 9-99)
Connection
→
Connection setup (page 9-99)
Only one ZSI-module can be connected per circuit-breaker.
If the ZSI-module is used together with other
Cubicle
BUS-modules,
the ZSI-module must be connected directly to the COM15-module
or the hand plug X8.
Summary of Contents for ARION WL Series
