Oce VarioPrint 1055 Configuration And Maintenance Manual Download Page 58

Page: 58 / 176

Chapter 7 Access security

Enable the Copy control device connected to the Network Printer

Enable the Copy control device connected to the Network
Printer

Introduction

The copy control device is connected externally to the machine. The system gives
access to external users who are not authorized in the accounts database. The
external user must insert coins or a credit card to gain access to the machine.

Océ Service must install and configure the Copy control device.

You can enable or disable an installed and configured copy control device.

An enabled Copy control device and an access-secured system (

see ‘About the

access-secured system of the Network Printer’ on page 50

) can be combined, to

enable use by internal and external user groups.

[47]

[47] Entry screen for external users

The following table displays the requirements for the external users when the copy
control device is enabled:

Summary of Contents for VarioPrint 1055

















































































































































































Search results

Summary of Contents for VarioPrint 1055

Reviews:

Related manuals for VarioPrint 1055

Brands by name

Popular brands

Oce VarioPrint 1055, Configuration And Maintenance Manual

Search results

Summary of Contents for VarioPrint 1055

Reviews:

Related manuals for VarioPrint 1055

Brands by name

Popular brands