Oce VarioPrint 1055 Configuration And Maintenance Manual Download Page 36 | Manualshive

Page: 36 / 176

background image

36

Chapter 5 Getting Started

Turn the machine on and off for daily use

Turn the machine on and off for daily use

Introduction

The machine has the following buttons.

■

ON / OFF button with green LED.
The ON / OFF button allows you to start the machine to do jobs. You can only
turn on or off the machine if the power switch is in '1' position and the start-up
phase was done. You can turn off and then back on the machine with the ON /
OFF button in particular circumstances, for example to correct an error. The
system requires 8 minutes to reach the operating temperature. When the machine
is ready, a message is displayed.

■

Power switch.
You can find the power switch at the left flank of the machine. The power switch
cuts and connects the power to the complete system (the machine and if available
the controller). Do not use the power switch to turn on and off the machine for
daily use (

see ‘Shut down the Digital Copier system’ on page 141

)(

see ‘Shut

down the Network Printer system’ on page 140

).

Before you begin

The Océ VarioPrint

®

1055/65/75 can have a key switch to protect access. If there is

a lock available, check to see if key is available.

Illustration

[33]

[33] The ON / OFF button

«
...
34
35
36
37
38
...
»

Summary of Contents for VarioPrint 1055

















































































































































































Reviews:

No comments

Related manuals for VarioPrint 1055

Brand: QMS Pages: 122

Brand: QMS Pages: 306

Brand: Canon Pages: 31

SCX 4500W - Personal Wireless Laser Multi-Function...

Brand: Samsung Pages: 113

imageRUNNER ADVANCE 8105

Brand: Canon Pages: 5

imageCLASS MF269dw

Brand: Canon Pages: 32

Brand: Samsung Pages: 158

Brand: Xerox Pages: 44

Brand: Printronix Pages: 9

Brand: MIMAKI Pages: 2

Brand: Oki Pages: 18

Brand: Oki Pages: 20

Brand: Oki Pages: 204

Brand: Olivetti Pages: 293

7760DX - Phaser Color Laser Printer

Brand: Xerox Pages: 4

VarioPrint 4110

Brand: Oce Pages: 216

DocuCentre-VI C2264

Brand: Fuji Xerox Pages: 129

Brand: Kyocera Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands