Nuvation Energy NUV100-CI-12-1 Product Manual Download Page 75

Page: 75 / 109

8. External Interfaces

8.1. Stack Switchgear

8.1.1. Battery Stack and DC Bus

The connectors use #M8 screws (included) and are intended for #M8 lugs (not included, e.g. Panduit
Corp LCMA50-8-L).

Flexible snap-on terminal covers are included. The maximum acceptable terminal lug tongue width is
1.1 inches and the maximum wire size is 4/0.

The recommended tightening torque is 5.7 to 6.8 N-m [50 to 60 in-lbs].

Table 13. Battery Stack and DC Bus Connector Assignment

Name

Description

Connected to Device

Battery (-)

Negative terminal of battery stack

Battery stack

Battery (+)

Positive terminal of battery stack

Battery stack

DC Bus (-)

Negative terminal of DC bus

External equipment

DC Bus (+)

Positive terminal of DC bus

External equipment

8.1.2. Ethernet

The Ethernet jack is a standard RJ45 Cat5e rated jack.

Table 14. Ethernet Connector Pin Assignment

Pin

Connection

Description

Connected to Device

TD_P

Transmit differential pair positive

External Equipment

TD_N

Transmit differential pair negative

External Equipment

RD_P

Receive differential pair positive

External Equipment

NUL45

Unused; connected to Pin 5 and terminated

External Equipment

NUL45

Unused; connected to Pin 4 and terminated

External Equipment

RD_N

Receive differential pair negative

External Equipment

NUL78

Unused; connected to Pin 8 and terminated

External Equipment

Nuvation Energy High-Voltage BMS - Product Manual

Document ID: NE-PM-003

Rev 1.2, 2021-03-03

Curie Update 1

Summary of Contents for NUV100-CI-12-1














































































































Search results

Summary of Contents for NUV100-CI-12-1

Reviews:

Related manuals for NUV100-CI-12-1

Brands by name

Popular brands

Nuvation Energy NUV100-CI-12-1, Product Manual

Search results

Summary of Contents for NUV100-CI-12-1

Reviews:

Related manuals for NUV100-CI-12-1

Brands by name

Popular brands