Nuvation Energy NUV100-CI-12-1 Product Manual Download Page 40 | Manualshive

Page: 40 / 109

background image

4.4.4. Connect the Link Bus Cable

Figure 35. Link Bus cable (NUVW-A01X03-010)

The Link Bus cable is used to connect Cell Interface modules in a daisy chain (called the Link Bus
chain) by connecting the 'Link In' of one Cell Interface to the 'Link Out' of the next Cell Interface. In
this series-connected chain of modules, each connection is made from the Link In connector of the
module with higher potential to the Link Out connector of the module with lower potential.

The Link Bus provides a data channel and a power source to subsequent Cell Interface modules in the
Link Bus chain. The amount of current supplied by this connector is the sum of current consumed by
all subsequent Cell Interface modules in the Link Bus chain.

Connection Procedure

1. Connect one end of the cable to the 'Link Out' connector on the Stack Switchgear.

2. Connect the other end of the Link Bus cable to the 'Link In' connector on the Cell Interface.

3. For multiple Cell Interface modules, use additional Link Bus cables to connect the 'Link Out' on

the current Cell Interface to the 'Link In' of the next Cell Interface in the chain.

4. The 'Link Out' of the last Cell Interface module in the Link Bus chain is to be left unconnected.

Nuvation Energy High-Voltage BMS - Product Manual

Document ID: NE-PM-003

36

Rev 1.2, 2021-03-03

Curie Update 1

«
...
38
39
40
41
42
...
»

Summary of Contents for NUV100-CI-12-1














































































































Reviews:

No comments

Related manuals for NUV100-CI-12-1

Brand: Samson Pages: 100

Brand: Radio Shack Pages: 3

Brand: Federal Signal Corporation Pages: 60

Brand: FASTRON. Pages: 16

Brand: Yealink Pages: 6

MeetingSpace VC800

Brand: Yealink Pages: 6

Brand: Yealink Pages: 16

Brand: Yealink Pages: 299

VC210 Teams Edition

Brand: Yealink Pages: 12

Brand: Yealink Pages: 16

Brand: Yealink Pages: 30

MeetingSpace VC200

Brand: Yealink Pages: 8

MVC Series: MVC800

Brand: Yealink Pages: 16

Brand: Yealink Pages: 8

Brand: Yealink Pages: 16

SYSMAC C500-NC222-E

Brand: Omron Pages: 164

Brand: Daruifuno Pages: 24

Liquitron DP5000-01A

Brand: LMI Technologies Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands