Nordson SDS 40-CC Meter Manual Download Page 25

Page: 25 / 32

SDS Meters

Part 1009912E

2005 Nordson Corporation

Item

Part

Description

Qty

Note

—

1053025

Meter, SDS40, 120V

—

1059119

Meter, SDS40, 240V

346088

Transducer, pressure, 5000 psi

1027169

Gun, SDS40 Auto-Flo, UHMW

945014

O-ring, hot paint,

tube

346073

Holder, rupture disk, 1000 psi

346072

Disc, rupture, 0.50, 5000 psi, 85 degree

111520

Cordset, SDS, 120V

1060683

Cordset, SDS, 240V

982636

Screw, button, M5 x 12

1060379

Cover

982178

Screw, Screw, M5 x 50

939220

Connector, wire, set screw

2/4

939586

Connector, 2-station

973402

Plug, , flush, 1/8

1052778

Cover, rear, bottom, heated, SDS

1060378

Body, connector, heated, SDS

1060375

Cover, right, heated, SDS

105223

Heater cartridge, 0.38 diameter, 200W, 120V, 3.75 in.

1060377

Cover, bottom, heated, SDS

1052777

Cover, front, heated, SDS

1016123

Gun, Auto-Flo, manifold, UHMW

1060376

Cover, left, heated, SDS

940133

O-ring, Viton, 0.426 ID x 0.070W

345508

Screw, socket, M12 x 40 mm, black

972119

Elbow, male,

tube x

NPT

1060686

Housing, heated, SDS, 40 cc, 120V

1060688

Housing, heated, SDS, 40 cc, 240V

1052779

Cover, rear, top, heated, SDS

1037633

Guard, front cover

NOTE

A: Order this part for 120V heated SDS meters.

B: Order this part for 240V heated SDS meters.

C: Use 2 connectors on 120V SDS meters. Use 4 connectors on 240V SDS meters.

Summary of Contents for SDS 40-CC Meter

































Search results

Summary of Contents for SDS 40-CC Meter

Reviews:

Related manuals for SDS 40-CC Meter

Brands by name

Popular brands

Nordson SDS 40-CC Meter, Manual

Search results

Summary of Contents for SDS 40-CC Meter

Reviews:

Related manuals for SDS 40-CC Meter

Brands by name

Popular brands