Nogueira PTN-1000 G3, Instruction Manual

Page: 123 / 152

Instructions Manual
47
ENGLISH
4. Preparation
A
B
G
F
CHOPPING OPTIONS DRUMS
GEARS
QTY.
OF
KNIVES
CHOPPING
SIZES
SPEED OF
THE DRUMS
SPROCKET
WHEELS
LENGTH OF THE
CHAIN
A B
Links Joint links
12 2 mm lower 1 Z11 Z30 63 1 CL + 1 HL
6 5 mm 2 Z11 Z25 61 1 CL
4 7,5 mm 3 Z16 Z30 63 3 HL +1 CL
3 10 mm 4 Z11 Z20 59 1 CL
5 Z16 Z25 63 1 CL + 1 HL
6 Z20 Z30 63 5 HL + 1 CL
7 Z11 Z16 57 1 HL + 1 CL
8 Z16 Z20 61 1 CL
9 Z20 Z25 63 2 HL + 1 CL
10 Z25 Z30 63 6 HL + 1 CL
11 Z20 Z16 61 1 CL
12 Z25 Z20 63 2 HL + 1 CL
13 Z25 Z16 63 1 CL + 1 HL
higher 14
Z25 Z11 61 1 CL
Use only the indicated sprocket gears
combinations
in the table above.
The use of combinations not indicated
will damage the platform and cause loss
of warranty.
ATTENTION!
CHOPPING OPTIONS DRUMS
GEARS
QTY.
OF
KNIVES
CHOPPING
SIZES
SPEED OF
THE DRUMS
SPROCKET
WHEELS
LENGTH OF THE
CHAIN
A B
Links Joint links
12 2 mm lower 1 Z11 Z30 63 1 CL + 1 HL
6 5 mm 2 Z11 Z25 61 1 CL
4 7,5 mm 3 Z16 Z30 63 3 HL +1 CL
3 10 mm 4 Z11 Z20 59 1 CL
5 Z16 Z25 63 1 CL + 1 HL
6 Z20 Z30 63 5 HL + 1 CL
7 Z11 Z16 57 1 HL + 1 CL
8 Z16 Z20 61 1 CL
9 Z20 Z25 63 2 HL + 1 CL
10 Z25 Z30 63 6 HL + 1 CL
11 Z20 Z16 61 1 CL
12 Z25 Z20 63 2 HL + 1 CL
13 Z25 Z16 63 1 CL + 1 HL
higher 14 Z25 Z11 61 1 CL
CHOPPING OPTIONS DRUMS
GEARS
QTY.
OF
KNIVES
CHOPPING
SIZES
SPEED OF
THE DRUMS
SPROCKET
WHEELS
LENGTH OF THE
CHAIN
A B
Links Joint links
12 2 mm
lower
1 Z11 Z30 63 1 CL + 1 HL
6 5 mm 2 Z11 Z25 61 1 CL
4 7,5 mm 3 Z16 Z30 63 3 HL +1 CL
3 10 mm 4 Z11 Z20 59 1 CL
5 Z16 Z25 63 1 CL + 1 HL
6 Z20 Z30 63 5 HL + 1 CL
7 Z11 Z16 57 1 HL + 1 CL
8 Z16 Z20 61 1 CL
9 Z20 Z25 63 2 HL + 1 CL
10 Z25 Z30 63 6 HL + 1 CL
11 Z20 Z16 61 1 CL
12 Z25 Z20 63 2 HL + 1 CL
13 Z25 Z16 63 1 CL + 1 HL
higher 14
Z25 Z11 61 1 CL
B
3.
In the chart you can see that for each
pair of sprockets-wheels (A) and (B)
corresponds a different speed of the
drums.
4.
The table shows speeds in ascending
order, from lowest to highest.
5.
Loosen the tensioner bolt (F);
6.
Move the tensioner to loosen the roller
chain (G);
7.
Remove the chain (G);
8.
Remove the sprocket wheels (A) and (B);
9.
Insert another pair of sprockets as intended
(increase or decrease speed).