EN
English –
6
After about 10 seconds, the motor performs a number of movements equal to the number impulses given with the transmitter.
04.
(on the new transmitter) Press the same key as you pressed in point 01 and hold it down while the motor performs 3 movements. Upon completion, release the
key.
Warning!
If the motor performs 6 movements, it means that its memory is full.
8
sec.
New
Old
01
02
5
sec.
1
/
2
/
3
/
...
/
10
sec.
New
Old
03
0,5
sec.
5
sec.
04
example
same
01
3
4
?
x 1
= Salita
x 2
= Salita dopo 10 secondi
x 3
= Salita dopo 20 secondi
x 4
= Discesa
x 5
= Discesa dopo 10 secondi
x 6
= Discesa dopo 20 secondi
x 7
= Passo-passo
x 8
= Stop
x 1
= Up
x 2
= Up after 10 seconds
x 3
= Up after 20 seconds
x 4
= Down
x 5
= Down after 10 seconds
x 6
= Down after 20 seconds
x 7
= Step-by-step
x 8
= Stop
5.9 -
Memorisation of a
climate sensor connected via radio
To perform the procedure you must have a transmitter (“old”) already memorised in “Mode 1”.
01.
(on the climate sensor) Keep the yellow key pressed for 10 seconds and then release it (in this case the motor does not perform any movement).
02.
(on the old transmitter) Press any key which has already been memorised three times (the motor will start performing the manoeuvre associated with that key).
03.
(on the climate sensor) Keep the yellow key pressed for 2 seconds: the motor performs 3 movements to confirm the memorisation.
Warning!
If the motor per-
forms 6 movements, it means that its memory is full.
10
sec.
2
sec.
Old
01
02
03
“
P1
”
“
P1
”
“
P1
”
X 3
0,5
sec.
example
3
Note
– When performing the procedure, you can cancel it at any time by keeping the
n
and
t
keys pressed simultaneously for 4 seconds. Otherwise, do not press
any key and wait 60 seconds for the motor to perform 6 movements.
5.10 -
Total or partial deletion of memory
This procedure allows you to choose under point 05 the data that you want to delete.
5.10.1 - Procedure performed with a transmitter memorised in “Mode I”
01.
Keep the
n
key pressed and wait for the motor to perform 2 movements. Upon completion, release the key.
02.
Keep the
s
key pressed and wait for the motor to perform 3 movements. Upon completion, release the key.
03.
Keep the
n
key pressed and wait for the motor to perform 3 movements. Upon completion, release the key.
04.
Keep the
t
key pressed and wait for the motor to perform 3 movements. Upon completion, release the key.
05.
•
To cancel the entire memory:
Keep the
s
and
t
keys pressed and wait for the motor to perform 5 movements. Upon completion, release the keys.
•
To delete all memorised transmitters
:
do not press any key and wait until the motor performs 5 movements.
•
To delete a single memorised transmitter
:
hold down the
s
key and wait for the motor to perform 3 movements. Now release the key.
Lastly, press the
button of the transmitter you wish to delete: the motor performs 5 movements.
•
To delete the limit switch heights (“0”, “1”) and intermediate heights (“H”): WARNING: – This deletion must be performed only when you want
to adjust the limit switch heights again, using a different procedure than the one used previously.
Keep the
n
key pressed and wait for the motor to
perform 5 movements. Upon completion, release the key.
5
sec.
01
04
03
02
5
sec.
5
sec.
all
data
(*)
all
05
05
“0”
“1”
“H”
05
5
sec.
5
sec.
5
sec.
2
3
5
5
5
05
3
5
sec.
3
single
(transmitter
to be
deleted)
key example
3
5
4 OPTIONS
Note
– When performing the procedure, you can cancel it at
any time by keeping the
n
and
t
keys pressed simultaneous-
ly for 4 seconds. Otherwise, do not press any key and wait 60
seconds for the motor to perform 6 movements.
