EN
3
– English
5.5 -
Memorising the FIRST transmitter
Warning
– Every time the motor is powered, 2 movements are performed if at least one transmitter and the limit switch heights are not in the memory.
Before starting the procedure, bring the awning to the midpoint of its stroke.
01.
Disconnect the power supply to the motor; wait 2 seconds and reconnect the power supply: the motor performs 2 movements and waits with no time limit.
02.
Keep the key
n
pressed and wait for the motor to perform three movements. Upon completion, release the key.
2
sec.
ON
OFF
01
02
5
sec.
3
2
Note
– After memorisation, the raising and lowering direction of the awning is not yet associated with the
s
and
t
respective keys of the transmitter. This combina-
tion will occur automatically when adjusting limit switches “
0
” and “
1
”; moreover, the rolling shutter will move in the “operator present” mode until the limit switches
are adjusted.
ming phases; refer to the procedures given in this manual and those given in the
manuals supplied with the devices.
PROGRAMMING AND ADJUSTMENTS
5
5.1 - General warnings
l
The limit switch must be adjusted after installing the motor in the awning and con-
necting it to the power supply.
l
In cases of installations with several motors and/
or receivers, before starting to program you must disconnect the electrical supply to
the motors and receivers you do not wish to program.
l
Scrupulously respect the
time limits indicated in the procedures: after releasing a key, you have 60 seconds
to press the next key indicated in the procedure; otherwise, when the time is up, the
motor will perform six movements to communicate cancellation of the procedure
in progress.
l
During programming, the motor performs a certain number of brief
movements, as a “response” to the command sent to the installer. It is important to
count the number of these movements without considering the direction in which
they are performed.
l
Every time the motor is powered, 2 movements are per-
formed if at least one transmitter and the limit switch heights are not in the memory.
5.2 - Positions in which the awning stops
automatically
The electronic system that controls the awning movement at all times can automati-
cally stop the movement when the awning reaches a certain position programmed
by the installer. The programmable positions are (see
fig. 6
):
– position “0” = upper limit switch: totally wound awning;
– position “1” = lower limit switch: totally unwound awning;
– position “H” = intermediate position: partially open awning.
When the limit switches are not programmed yet, the awning can be moved only in
the “hold-to-run” mode, i.e. keeping the control key pressed for the desired duration
of the manoeuvre; the movement stops as soon as the user releases the key. How-
ever, after programming the limit switches, briefly pressing the appropriate key will
start the awning and it will stop moving automatically as soon as the awning reaches
the required position.
The programming of the limit switches simultaneously combines the two directions
of rotation of the motor to the respective shutter raising key (
s
) and shutter lowering
key (
t
) of the control device (initially, when the limit switches are not programmed
yet, the combination is random and it can happen that when pressing the
s
key, the
shutter moves down instead of up, or vice versa).
5.3 - Overview of the transmitters
5.3.1 - Compatible transmitters
Consult the Nice product catalogue or go to www.niceforyou.com to find the Nice
devices compatible with the radio receiver built into the motor.
5.3.2 - Transmitter memorisation hierarchy
In general a transmitter can be memorised as a FIRST transmitter or a SECOND
transmitter (or third, fourth, etc.).
A - First transmitter
A transmitter can be memorised as a first transmitter only if in the motor no
other transmitter is memorised. For this memorisation, follow procedure 5.5 (this
memorises the transmitter in “Mode I”.
B -
Second (or third, fourth, etc.) transmitting device or climate sensor
A portable transmitter (or a radio climate sensor) can be memorised as a second
(or third, fourth, etc.) transmitting device only if the First Transmitter is already
memorised in the motor. For this memorisation, follow one of the procedures
given in section 5.8.
5.3.3 - Two procedures to memorise the keys of a transmitter
To memorise the keys of a transmitter, two different procedures can be used: “Mode
I” and “Mode II”.
l
“
MODE I
” – This mode automatically transfers, the various commands available
in the motor, all together, into the various keys available on the transmitter, without
allowing the installer to change the combinations of commands and keys. Upon
completion of the procedure, each key will be combined with a command according
to the following diagram.
- key
s
(or key
1
): will be combined with
Raise
- key
n
(or key
2
): will be combined with the command
Stop
- key
t
(or key
3
): will be combined with the command
Lower
(if there is a fourth key on the transmitter .....)
- key
4
: will be combined with the command
Stop
Note
– If the keys of your transmitter have no symbols or numbers, see
fig. 2
to
identify them.
l
“
MODE II
” – This mode allows you to manually combine one of the commands
available in the motor with one of the transmitter keys, giving the installer the option
of choosing the command and key combinations to use. At the end of the proce-
dure, to memorise another key with another command desired, it will be necessary
to repeat the procedure once again.
Warning!
– Each automation has its own list of commands that can be memorised
in Mode II; in the case of the present motor the list of commands available is given
in procedure 5.8.2.
5.3.4 - Number of transmitters that can be memorised
You can memorise 30 transmitters (including any radio climate sensors) if these are
all memorised in “Mode I”, or you can memorise 30 single commands (keys) if they
are all memorised in “Mode II”. The two modes can coexist up to a maximum limit
of 30 memorised units.
5.4 - Transmitter to the used for programming
procedures
l
The programming procedures can be performed exclusively with a Nice
transmitter having at least the following keys
s
,
n
,
t
.
l
The programming procedures must be performed exclusively with a transmitter
memorised in “Mode I” (paragraph 5.5 or 5.8.1).
l
If the transmitter used for programming controls multiple automation units, you
must select the “unit” corresponding to the automation you are programming be-
fore sending a command during a procedure.
