© 2021 Copyright Newmar Corporation. All rights reserved. For the most up-to-date version of this content, and for more product-specific information, please refer to Newgle.
133
HVAC
FAN
Press the FAN button to select the desired fan speed.
Each successive press will advance to the next available
speed. Your selections will be “Auto”, “LOW”, “MED”,
and “HIGH”. The fan will run continuously during “LOW”,
“MED”, and “HIGH” fan settings. The fan will cycle ON
and OFF with the thermostat on “AUTO” setting.
CLOCK
Press the CLOCK button to initiate the clock setting sub-
menu on the CCC 2 thermostat. When in this menu, the
hour digits will flash first. The hour can be adjusted using
the ▲ or ▼ buttons. Press the CLOCK button again and
the minute digits will flash, allowing the minute setting to
be adjusted using the ▲ or ▼ buttons. Press it a third time
and the AM or PM icon will flash, allowing the AM or PM
setting to be adjusted using the ▲ or ▼ buttons. Press it
one more time to store the new time in memory and exit
the clock setting sub-menu.
ZONE BUTTON
Press the ZONE button to cycle the LCD display through
the available zone selections; “Zone 1”, “Zone 2”, “Zone
3”, and “Zone 4”. Only the available zones installed within
your system will display.
MODE
Press the MODE button and the LCD will display the first
available mode. Each successive press will advance to
the next available mode. Continue to press the MODE
button until the desired mode appears. Depending on
the systems installed, your choices will be “OFF”, “COOL”,
“AUTO”, “HP”, “FURN” or “AQUA”, “HS”, and “FAN”.
•
OFF = off
•
COOL = setting for air conditioning
•
AUTO = allows the thermostat to determine to use
one of the heating options or cooling option to
maintain a set temperature
•
HP = heat pump setting to use A/C to heat instead of
cool
•
FURN = furnace setting to use the furnace for heating
•
AQUA = coaches with Aqua Hot heating systems for
heat instead of a furnace
•
HS = heat strip (Newmar does not use this function,
so it is likely that this option will not show up on the
thermostat; however, if the dip switch for the heat
strip is turned on, it will appear)
•
FAN = fan only allows you to use the fan to move air
without heating or cooling
Source(s): Dometic Comfort Control Center 2 Thermostat Operating
Instructions (REV B, 08/16)
Product(s): Dometic Comfort Control II Thermostat (Model: 3314082,
Newmar Part Number: 142252)
Periodic cleaning or replacement of the air
conditioner/heat pump air filters is required. NEVER
run the air conditioner without the air filter in place.
This may plug the unit evaporator coil with dirt and
may substantially degrade the performance of the
unit over time.
IMPORTANT
!
This procedure may need to be completed on each zone.
NOTE FROM NEWMAR
Care and Maintenance
When a system fan run time exceeds 1000 hours, the
filter icon is displayed on the LCD. When this occurs,
wash the filter with soap and warm water. Let dry and
reinstall.
To reset the fan run time and clear the filter icon, hold the
INSIDE TEMP and °F/°C buttons for 3 seconds. This will
clear the fan run time for the current zone selected.
TEMPERATURE SET-POINT
Press the ▲ or ▼ button to change the temperature
set-point. The temperature set-point is indicated by (2)
digits on the LCD. Press the ▲ button to increase and
the ▼ button to decrease the temperature set-point. The
maximum set-point for the system is 90 °F (32 °C). The
minimum set-point is determined by the active operating
mode. For heating, the minimum is 40 °F (4 °C) and
minimum for cooling is 55 °F (13 °C).
TEMPERATURE FORMAT °F / °C
Press the °F / °C button to switch between Fahrenheit
and Centigrade format. “°F” indicates Fahrenheit and “°C”
indicates Centigrade.
INSIDE TEMPERATURE
Press and hold the INSIDE TEMP button and the LCD
will display the current inside temperature recorded at
the CCC 2 thermostat (or at the optional remote indoor
temperature sensor) instead of the temperature set-point.
The LCD will also display “IN” to indicate that the inside
temperature is being displayed. When the INSIDE TEMP
button is released, the LCD will return to the programmed
temperature set-point.
Summary of Contents for Bay Star 2022
Page 1: ...SM 2022...
