NETGEAR R6400v2 User Manual Download Page 110

Page: 110 / 178

Specify Network Settings

110

AC1750

Smart WiFi Router

The user name is

admin

. The user name and password are case-sensitive.

The BASIC Home page displays.

Select

ADVANCED > Setup > LAN Setup

In the

IP Address

field, type the IP address.

In the

IP Subnet Mask

field, type the subnet mask of the router.

The IP address and subnet mask identify which addresses are local to a specific device
and which must be reached through a gateway or router.

Change the RIP settings.

Router Information Protocol (RIP) allows a router to exchange routing information with
other routers.

In the

RIP Direction

menu, select one of the following:

Both

. The router broadcasts its routing table periodically and incorporates

information that it receives.

Out Only

. The router broadcasts its routing table periodically.

In Only

. The router incorporates the RIP information that it receives.

In the

RIP Version

menu, select one of the following:

Disabled

. This is the default setting.

RIP-1

. This format is universally supported. It is adequate for most networks,

unless your network setup is unusual.

RIP-2

. This format carries more information. Both RIP-2B and RIP-2M send the

routing data in RIP-2 format. RIP-2B uses subnet broadcasting. RIP-2M uses
multicasting.

Click the

Apply

button.

Your changes are saved.

Summary of Contents for R6400v2



















































































































































































Search results

Summary of Contents for R6400v2

Reviews:

Related manuals for R6400v2

Brands by name

Popular brands

NETGEAR R6400v2, User Manual

Search results

Summary of Contents for R6400v2

Reviews:

Related manuals for R6400v2

Brands by name

Popular brands