Ness SDI User Manual Download Page 13

Page: 13 / 61

Digital Video Recorder for Ness IQ-Series

CAUTION

HDMI CONNECTION MAY NOT BE COMPATIBLE WITH CERTAIN OUTPUT DEVICE.

VIDEO NOISE MAY OCCUR DEPENDING ON THE TYPE OF HDMI CABLE USED. MAKE SURE TO USE AN HDMI

CAUTION

BLACK SCREEN WILL APPEAR IF THE MONITOR DOEST NOT SUPPORT THE SELECTED RESOLUTION. UNLESS USER PRESS

DURING BLACK SCREEN, SYSTEM WILL AUTOMATICALLY GO BACK TO THE PREVIOUS RESOLUTION IN 15 SECONDS.

1.5.4 Audio Connections

Connect an audio device to ‘AUDIO IN’ and a speaker system to ‘

adjustable.

1.5.5 TCP/IP(Ethernet) Connections

Connect to ‘ETHERNET’ connector with the LAN cable.

When connect to Internet, use an ordinary LAN cable (Non

use only ‘Crossover cable’.

1.5.6 Alarm Connections(TTL)

Connect Alarm Input (Sensor) to ‘AI 1~AI

Connect Alarm Output (buzzer, siren, etc.) to ‘

1.5.7 Master Alarm

Alarm In sensor will be deactivated if Master Alarm is on.

Connect Master Alarm

In to ‘

M’ connectors.

1.5.8 Alarm Connections(Relay (Dry Contact)

Connect Alarm Output (buzzer, siren, etc.) to ‘

to ‘GND’ connector.

1.5.9 RS-485/422 Connections

PTZ Camera connector.

Please use TX+, TX-, RX+ and RX- terminals.

1.5.10 RS-485 Over Coax Connection

PTZ Camera Connector

Please connect Coax to ‘Video In’ and select any Protocol in Camera/PTZ setup.

NOTE

PTZ Camera must support RS-485 over Coax function

NOTE

When selecting Protocol, user can choose any protocol from the Protocol list other than

485 over Coax will not work.

Series 960H & SDI DVR

HDMI CONNECTION MAY NOT BE COMPATIBLE WITH CERTAIN OUTPUT DEVICE.

DEPENDING ON THE TYPE OF HDMI CABLE USED. MAKE SURE TO USE AN HDMI

BLACK SCREEN WILL APPEAR IF THE MONITOR DOEST NOT SUPPORT THE SELECTED RESOLUTION. UNLESS USER PRESS

DURING BLACK SCREEN, SYSTEM WILL AUTOMATICALLY GO BACK TO THE PREVIOUS RESOLUTION IN 15 SECONDS.

’ and a speaker system to ‘AUDIO OUT’. Please use a speaker system with volume

TCP/IP(Ethernet) Connections

’ connector with the LAN cable.

When connect to Internet, use an ordinary LAN cable (Non-cross cable). However, when connect

TTL)

ct Alarm Input (Sensor) to ‘AI 1~AI 4 (or AI 16)’ connectors and connect Sensor Common to ‘G’ connector.

Connect Alarm Output (buzzer, siren, etc.) to ‘AO 1~AO 4 (or AO 16)’ connectors and connect Common to ‘

be deactivated if Master Alarm is on.

’ connectors.

Relay (Dry Contact))

Connect Alarm Output (buzzer, siren, etc.) to ‘NO or NC 1~ NO or NC 2’ connectors, Power to ‘

485/422 Connections

terminals.

Connection

select any Protocol in Camera/PTZ setup..

485 over Coax function in order to use this feature.

When selecting Protocol, user can choose any protocol from the Protocol list other than ‘NONE’. If ‘NONE’ is selected then

Page 13

DEPENDING ON THE TYPE OF HDMI CABLE USED. MAKE SURE TO USE AN HDMI-CERTIFIED CABLE

BLACK SCREEN WILL APPEAR IF THE MONITOR DOEST NOT SUPPORT THE SELECTED RESOLUTION. UNLESS USER PRESS ‘OK’

DURING BLACK SCREEN, SYSTEM WILL AUTOMATICALLY GO BACK TO THE PREVIOUS RESOLUTION IN 15 SECONDS.

’. Please use a speaker system with volume

cross cable). However, when connect directly to a PC, please

16)’ connectors and connect Sensor Common to ‘G’ connector.

’ connectors and connect Common to ‘G’ connector.

to ‘COM’ connector and Ground

is selected then RS-

Summary of Contents for SDI






























































Search results

Summary of Contents for SDI

Reviews:

Related manuals for SDI

Brands by name

Popular brands

Ness SDI, User Manual

Search results

Summary of Contents for SDI

Reviews:

Related manuals for SDI

Brands by name

Popular brands