Ness D16 Installation & Programming Manual Download Page 54 | Manualshive

Page: 54 / 64

background image

54

54

54

54

54

P R O G R A M M I N G

NESS D16 (V4.6) CONTROL PANEL - INSTALLER MANUAL

REQUIRED RINGS

Sets the number of double-rings before an incoming call is answered. This is
used for Remote Access.

Programmable from 1 to 16 rings. Enter a value between 1 and 16.

PROGRAMMING SEQUENCE:

P91E

existing Required Rings value is displayed

[ENTER NEW VALUE] E

new Required Rings value is displayed

P91E

PROGRAM MODE LEVEL:

Installer, Remote by PC

FACTORY DEFAULT:

1

NOTES:

• RELATED OPTIONS:

P90E 1E to 8E

(Remote Access options)

OPTION No

DESCRIPTION

DEFAULT

NOTE

P91E

Required Rings to answer

1

SEND DIALLER TEST REPORT

Send a Dialler Test Report to the telephone numer programmed at P70E.
This test operates only in User program mode.

P66666666E

(eight 6’s) Triggers dialler and sends test report to Central Station

SIREN TEST

Turn the Siren, Reset and Strobe Outputs On. Pressing P E will stop the Siren Test (and
also exits Program Mode).
This test operates in User and Installer program mode.

P77777777E

(eight 7’s) Triggers Siren, Reset, Strobe

PANEL RESET

This function resets the microprocessor. The effect is the same as powering down and
powering up again. Panel Reset operates in User and Installer program mode.

P88888888E

(eight 8’s) Panel Reset

PANEL SOFTWARE VERSION

This function displays the panel software version when in program mode. Displayed in
decimal format by the zone LEDs.
Example, version 4.5 is displayed by flashing 4 followed by 5.
This test operates in User and Installer program mode.

P999999999E

(eight 9’s) Displays software version

OPTION No

DESCRIPTION

1

2

3

4

5

6

7

8

9

10

11 12

13 14 15 16

Zones

P94E

"No memory warning" zones

SPECIAL FUNCTIONS

NO MEMORY WARNING ZONES

Select zones 1 to 8 that do not flash the Memory indicator. The alarm still goes
into memory and can be seen when reviewing. (Only zones 1 to 8 can be
selected on either the D8 or D16 panels.)

PROGRAMMING SEQUENCE:

P94E 1E-8E

toggles the option ON and OFF

P94E 1E-8E OFF: Memory Warning operates normally for that zone
P94E 1E-8E ON: Memory Warning is disabled for that zone

P94E

PROGRAM MODE LEVEL:

Installer, Remote by PC

FACTORY DEFAULT:

no zones selected

NOTES:

•

0E

will turn all selections OFF

MEMORY E

will turn all selections ON

Technical Manuals Online! - http://www.tech-man.com

«
...
52
53
54
55
56
...
»

Summary of Contents for D16

































































Reviews:

No comments

Related manuals for D16

Brand: Samson Pages: 48

Brand: Mako Networks Pages: 15

Brand: Gardena Pages: 16

Brand: MADRIX Pages: 28

Brand: MacDon Pages: 32

Brand: K&K Pages: 6

Brand: Omnex Pages: 9

Brand: Omegon Pages: 6

Brand: WATERLOO Pages: 8

Brand: Xantrex Pages: 56

Brand: Xantrex Pages: 2

Freedom Sequence

Brand: Xantrex Pages: 58

Brand: Xantrex Pages: 4

Brand: Xantrex Pages: 20

Brand: L-Acoustics Pages: 24

Brand: L-Acoustics Pages: 21

Brand: M&S Systems Pages: 4

Brand: YOKOGAWA Pages: 150

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands