Ness D16 Installation & Programming Manual Download Page 49

Page: 49 / 64

P R O G R A M M I N G

NESS D16 (V4.6) CONTROL PANEL - INSTALLER MANUAL

FORCED OPENING REPORT

If Forced Opening Report is selected ON - when an alarm has been reset by a
valid User Code (or Radio Key), the dialler will send an Opening report along
with a restoral report for the zone or miscellaneous input which caused the
alarm.

PROGRAMMING SEQUENCE:

P88E 5E

toggles the option ON and OFF

P88E 5E OFF: No Forced opening Reports
P88E 5E ON:

Forced opening Reports enabled

P88E 5E

PROGRAM MODE LEVEL:

Installer, Remote by PC

FACTORY DEFAULT:

ON: Forced opening Reports enabled

NOTES:

• This option is used to indicate to the

Central Station that an alarm has been
reset by a valid user.

Usually used in cases where Open/Close

reports are normally selected OFF.

DELAY CLOSING REPORT

If selected ON, Closing reports (if enabled) are sent at the end of Exit Time.
Normally, Closing reports are sent immediately on Arming.

PROGRAMMING SEQUENCE:

P88E 6E

toggles the option ON and OFF

P88E 6E OFF: Closing Reports sent on Arming
P88E 6E ON:

Closing Reports sent at end of Exit Time

P88E 6E

PROGRAM MODE LEVEL:

Installer, Remote by PC

FACTORY DEFAULT:

OFF: Closing Reports sent on Arming

NOTES:

• RELATED OPTIONS:

P88E 1E

AREA1 Open/Close reports

P88E 2E

AREA2 Open/Close reports

MANUAL EXCLUDE REPORT

Enables Manual Exclude Reports for Zones 1-16. Exclude Reports for 24hr
zones are sent on exiting EXCLUDE mode.

PROGRAMMING SEQUENCE:

P88E 7E

toggles the option ON and OFF

P88E 7E OFF: No Manual Exclude Reports
P88E 7E ON:

Manual Exclude Reports enabled

P88E 7E

PROGRAM MODE LEVEL:

Installer, Remote by PC

FACTORY DEFAULT:

ON: Manual Exclude Reports enabled

NOTES:

• RELATED OPTIONS:

P88E 8E

Auto Exclude Reports

AUTO EXCLUDE REPORT

Enables Auto Exclude Reports for Zones 1-16. Zones not sealed on Arming will
be reported as Auto Excluded..

PROGRAMMING SEQUENCE:

P88E 8E

toggles the option ON and OFF

P88E 8E OFF: No Auto Exclude Reports
P88E 8E ON:

Auto Exclude Reports enabled

P88E 8E

PROGRAM MODE LEVEL:

Installer, Remote by PC

FACTORY DEFAULT:

ON: Auto Exclude Reports enabled

NOTES:

•

P88E 7E

Manual Exclude Reports

Technical Manuals Online! - http://www.tech-man.com

Summary of Contents for D16

































































Search results

Summary of Contents for D16

Reviews:

Related manuals for D16

Brands by name

Popular brands

Ness D16, Installation & Programming Manual

Search results

Summary of Contents for D16

Reviews:

Related manuals for D16

Brands by name

Popular brands