NEC mPD17120 Subseries User Manual Download Page 172

Page: 172 / 289

CHAPTER 14 INTERRUPT FUNCTIONS

157

Figure 14-4. Interrupt Acceptance Timing Chart (INTE=1 and IP

×××

=1) (3/3)

<8> When an interrupt has occurred during skipping (NOP handling) by a skip instruction

Remarks 1.

The INT cycle is for preparing interrupts. During this cycle, PC and PSWORD saving and IRQ clearing

are performed.

For execution of the MOVT instruction, two instruction cycles are exceptionally required.

The EI instruction is considered to prevent multiple interrupts from occurring when returning from

the interrupt operation.

Machine cycle

Instruction

IRQ

×××

Skip instruction

INT cycle

Vector address
instruction

Interrupt occurrence recognized

Handled as NOP

Summary of Contents for mPD17120 Subseries


































































































































































































































































































Search results

Summary of Contents for mPD17120 Subseries

Reviews:

Brands by name

Popular brands

NEC mPD17120 Subseries, User Manual

Search results

Summary of Contents for mPD17120 Subseries

Reviews:

Brands by name

Popular brands