manualshive.com logo in svg

NEC mPD17120 Subseries, User Manual

Share
Download
NEC mPD17120 Subseries User Manual Download Page 145

CHAPTER 13   PERIPHERAL HARDWARE

130

13.1.9  Timer Resolution and Maximum Setting Time

Table 13-1 shows the timer resolution in each source clock and maximum setting time.

Table 13-1.  Timer Resolution and Maximum Setting Time

Mode Register

Timer

TMCK1

TMCK0

Resolution

Maximum Setting Time

0

0

32 

µ

s

8.192 ms

0

1

4 

µ

s

1.024 ms

1

0

256 

µ

s

65.536 ms

1

1

INT pin 

Note 2

0

0

approx. 61.1 

µ

s

approx. 15.6 ms

0

1

approx. 7.64 

µ

s

approx. 1.9 ms

1

0

approx. 489 

µ

s

approx. 125 ms

1

1

INT pin 

Note 2

0

0

128 

µ

s

32.768 ms

0

1

16 

µ

s

4.096 ms

1

0

1.024 ms

262.144 ms

1

1

INT pin 

Note 2

0

0

512 

µ

s

131.072 ms

0

1

64 

µ

s

16.384 ms

1

0

4.096 ms

1.048576 s

1

1

INT pin 

Note 2

Notes

1.

The guaranteed frequency range of oscillation for the 

µ

PD17120/17132/17P132 is f

CC

=400 kHz to

2.4 MHz.

2.

High/low level width of INT pin is 10 

µ

s (MIN.) when V

DD

=4.5 to 5.5 V, and 50 

µ

s (MIN.) when V

DD

=2.7

to 5.5 V.  Refer to Data Sheet for detailed information.

System Clock

At 8 MHz 

Note1

At 4.19 MHz 

Note1

At 2 MHz

At 500 kHz

Summary of Contents for mPD17120 Subseries


































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands