NEC Express5800/120Rh-2 Page 218 User Manual Download | Manualshive

Page: 218 / 406

background image

6-20 Installing and Using Utilities

Adaptec Storage Manager



Adaptec Storage Manager



(hereinafter abbreviated to ASM) is an application that locally or

remotely manages HostRAID storage system and provides RAID functions through the SCSI
interface on the Windows Server 2003 x64 Edition in your server. You can use the following
functions for HostRAID by installing ASM in your system.

Features

Creating disks at a level of RAID0, RAID1, or RAID10

Creating Hot Spare disks that are to be used for automatically executing Rebuild if a
redundant disk array enters the Degraded state

Making a consistency check on redundant disk arrays

Recording HostRAID events into the event log

Before attempting to operate ASM, read the "Adaptec Storage Manager



User's Guide" included in

NEC EXPRESSBUILDER CD-ROM. The manual explains the ASM installation procedure and
notes on operating ASM.

IMPORTANT:

You cannot install ASM with EXPRESS Setup. Install

ASM manually.

«
...
216
217
218
219
220
...
»

Summary of Contents for Express5800/120Rh-2























































































































































































































































































































































































































Reviews:

No comments

Related manuals for Express5800/120Rh-2

Brand: Datacom Pages: 89

Brand: IBM Pages: 74

A+ AS-2124US-TNRP

Brand: Supermicro Pages: 130

Brand: Avaya Pages: 84

4-Port USB 2.0 Device Server over IP...

Brand: Quatech Pages: 2

Brand: Atop Pages: 2

C12C823912 - Net 2 Print Server

Brand: Epson Pages: 20

C823622A - Interface Type B Print Server

Brand: Epson Pages: 3

C12C800WN (Net 802.11b Wireless Print Server)

Brand: Epson Pages: 2

C32C824461 - UB R03 Print Server

Brand: Epson Pages: 86

Brand: Epson Pages: 279

C823622A - Interface Type B Print Server

Brand: Epson Pages: 2

PRIMERGY RX100 S7

Brand: Fujitsu Pages: 86

PRIMERGY RX1330 M1

Brand: Fujitsu Pages: 312

Primergy RX100 S4

Brand: Fujitsu Pages: 85

PRIMERGY RX1330 M1

Brand: Fujitsu Pages: 84

Primergy RX100 S3

Brand: Fujitsu Pages: 73

PRIMERGY RX100 S8

Brand: Fujitsu Pages: 82

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands